The detach function declaration in `ISC__REFCOUNT_TRACE_DECL` had an
returned an accidental implicit int. While not allowed since C99, it
became an error by default in GCC 14.
`ISC_REFCOUNT_TRACE_IMPL` and `ISC_REFCOUNT_STATIC_TRACE_IMPL` expanded
into the wrong macros, trying to declare it again with the wrong number
of parameters.
- duplicated question
- duplicated answer
- qtype as an answer
- two question types
- question names
- nsec3 bad owner name
- short record
- short question
- mismatching question class
- bad record owner name
- mismatched class in record
- mismatched KEY class
- OPT wrong owner name
- invalid RRSIG "covers" type
- UPDATE malformed delete type
- TSIG wrong class
- TSIG not the last record
there were TSAN error reports because of conflicting uses of
node->dirty and node->nsec, which were in the same qword.
this could be resolved by separating them, but we could also
make them into atomic values and remove some node locking.
The fix_iterator() function had a lot of bugs in it and while fixing
them, the number of corner cases and the complexity of the function
got out of hand. Rewrite the function with the following modifications:
The function now requires that the iterator is pointing to a leaf node.
This removes the cases we have to deal when the iterator was left on a
dead branch.
From the leaf node, pop up the iterator stack until we encounter the
branch where the offset point is before the point where the search key
differs. This will bring us to the right branch, or at the first
unmatched node, in which case we pop up to the parent branch. From
there it is easier to retrieve the predecessor.
Once we are at the right branch, all we have to do is find the right
twig (which is either the twig for the character at the position where
the search key differs, or the previous twig) and walk down from there
to the greatest leaf or, in case there is no good twig, get the
previous twig from the successor and get the greatest leaf from there.
If there is no previous twig to select in this branch, because every
leaf from this branch node is greater than the one we wanted, we need
to pop up the stack again and resume at the parent branch. This is
achieved by calling prevleaf().
Move the fix_iterator out of the loop and only call it when we found
a leaf node. This leaf node may be the wrong leaf node, but fix_iterator
should correct that.
Also, when we don't need to set the iterator, just get any leaf. We
only need to have a leaf for the qpkey_compare and the end result does
not matter if compare was against an ancestor leaf or any leaf below
that point.
An obscured DNSKEY RRset at a delegation was incorrectly added to
the NSEC/NSEC3 type bit map leading to zone verification failures.
This adds such a RRset to the test zone.
DNSSEC only works when DNSKEYs are self signed. This only occurs
when the DNSKEY RRset is at the apex. Cause dnssec-signzone to
fail if it attempts to sign an non-apex DNSKEY RRset.
An assertion failure would be triggered when sending the TCP data ends
after the TCP reading gets closed. Implement proper reference counting
for the isc_httpd object.
When searching for a requested name in dns_qp_lookup(), we may add
a leaf node to the QP chain, then subsequently determine that the
branch we were on was a dead end. When that happens, the chain can be
left holding a pointer to a node that is *not* an ancestor of the
requested name.
We correct for this by unwinding any chain links with an offset
value greater or equal to that of the node we found.
The code below the if/else construction could only be run if the 'if'
code path was taken. Move the code into the 'if' code block so that
it is more easier to read.
The list isn't exactly maintained but it helped with some BIND history
tracking and is basically harmless so it might be worth holding onto it.
I have adapted the name to ASCII so IDN support won't be necessary.
The high-water allows administrators to better tune the recursive
clients limit without having to to poll the statistics channel in high
rates to get this number.
Returning the value allows for better high-water tracking without
running into edge cases like the following:
0. The counter is at value X
1. Increment the value (X+1)
2. The value is decreased multiple times in another threads (X+1-Y)
3. Get the value (X+1-Y)
4. Update-if-greater misses the X+1 value which should have been the
high-water
To avoid any escaping issues or messing with a language-specific format
when the variable has to be parsed, create a dedicated file for each
variable that is obtained from autoconf.
