Detection of the Dallas/Maxim DS1621, DS1625 and DS1631 chips is weak
and likely to result in false positive. There's no rationale for
keeping it in sensors-detect as these chips are not found in desktop
computer systems. So drop detection of these chips altogether.
So we can not use the chip revision to detect the actual chip.
Merge entries for NCT5577D and NCT6776F into one.
List NCT5572D as another variant of W83677HG-I (NCT6775).
NCT6106D chip ID as observed on a real system is 0xC452, not 0x1061 as
claimed by the data sheet. Confirmed with Nuvoton that the correct
chip ID is 0xC452. Also list its variants NCT6102D and NCT6104D.
List NCT5532D as variant of NCT6779D. Data sheets list possible chip
IDs of 0xC561 and 0xC562, so detect and accept all chip revisions.
Point to new nct6775 driver for NCT6775, NCT6776, and NCT6779.
Patch from Jaromir Capik.
The device file /dev/port might be missing in some cases
and the sensors detection is terminated when the user
tries to detect sensors dependent on it's existence.
That's not correct -> it's not a reason for terminating
the detection.
/proc/modules so we will try to load it, even though it's already
available. It will succeed, however later attempts to remove the
driver will fail and such failures are reported at the end of the
script, which can be confusing.
So, use /sys/module instead of /proc/modules where available, as
built-in drivers are listed there too so we no longer attempt to load
already available drivers. As a consequence we also no longer attempt
to remove the drivers in question, thus clearing the error message.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@6114 7894878c-1315-0410-8ee3-d5d059ff63e0
Take multiplexers into account when looking up the parent device of
each I2C adapter. We don't bother with old kernels as they didn't have
support for multiplexers anyway.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@6085 7894878c-1315-0410-8ee3-d5d059ff63e0
Don't probe I2C buses on graphics cards by default. Their drivers will
typically instantiate the I2C slave devices themselves as needed, and
such probes have been occasionally reported to cause serious trouble.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@6084 7894878c-1315-0410-8ee3-d5d059ff63e0
LM96080. It is functionally compatible with the LM80 but detection is
completely different.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@6018 7894878c-1315-0410-8ee3-d5d059ff63e0
systems where /dev/cpu/0/cpuid is part of the static device node tree,
the previous test would succeed even when the cpuid module isn't
loaded, resulting in missing detections (of coretemp-supported CPU
models in particuler.) Check if the module is loaded by looking in
sysfs instead, this is much more reliable.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@5993 7894878c-1315-0410-8ee3-d5d059ff63e0
EMC2300 is already detected, but is reported as EMC6D103S. These
two are register compatible and it's not actually possible to
distinguish between them by registers.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@5973 7894878c-1315-0410-8ee3-d5d059ff63e0
