mirror of
https://github.com/openvswitch/ovs
synced 2025-10-29 15:28:56 +00:00
ec9f40dce1
Flagged with: https://github.com/lyda/misspell-check Run with: git ls-files | misspellings -f - Signed-off-by: Andy Hill <hillad@gmail.com> Signed-off-by: Ben Pfaff <blp@nicira.com>
73 lines
3.4 KiB
Plaintext
73 lines
3.4 KiB
Plaintext
Using LISP tunneling
|
|
====================
|
|
|
|
LISP is a layer 3 tunneling mechanism, meaning that encapsulated packets do
|
|
not carry Ethernet headers, and ARP requests shouldn't be sent over the
|
|
tunnel. Because of this, there are some additional steps required for setting
|
|
up LISP tunnels in Open vSwitch, until support for L3 tunnels will improve.
|
|
|
|
This guide assumes tunneling between two VMs connected to OVS bridges on
|
|
different hypervisors reachable over IPv4. Of course, more than one VM may be
|
|
connected to any of the hypervisors, and a hypervisor may communicate with
|
|
several different hypervisors over the same lisp tunneling interface. A LISP
|
|
"map-cache" can be implemented using flows, see example at the bottom of this
|
|
file.
|
|
|
|
There are several scenarios:
|
|
|
|
1) the VMs have IP addresses in the same subnet and the hypervisors are also
|
|
in a single subnet (although one different from the VM's);
|
|
2) the VMs have IP addresses in the same subnet but the hypervisors are
|
|
separated by a router;
|
|
3) the VMs are in different subnets.
|
|
|
|
In cases 1) and 3) ARP resolution can work as normal: ARP traffic is
|
|
configured not to go through the LISP tunnel. For case 1) ARP is able to
|
|
reach the other VM, if both OVS instances default to MAC address learning.
|
|
Case 3) requires the hypervisor be configured as the default router for the
|
|
VMs.
|
|
|
|
In case 2) the VMs expect ARP replies from each other, but this is not
|
|
possible over a layer 3 tunnel. One solution is to have static MAC address
|
|
entries preconfigured on the VMs (e.g., `arp -f /etc/ethers` on startup on
|
|
Unix based VMs), or have the hypervisor do proxy ARP.
|
|
|
|
On the receiving side, the packet arrives without the original MAC header.
|
|
The LISP tunneling code attaches a header with harcoded source and destination
|
|
MAC address 02:00:00:00:00:00. This address has all bits set to 0, except the
|
|
locally administered bit, in order to avoid potential collisions with existing
|
|
allocations. In order for packets to reach their intended destination, the
|
|
destination MAC address needs to be rewritten. This can be done using the
|
|
flow table.
|
|
|
|
See below for an example setup, and the associated flow rules to enable LISP
|
|
tunneling.
|
|
|
|
+---+ +---+
|
|
|VM1| |VM2|
|
|
+---+ +---+
|
|
| |
|
|
+--[tap0]--+ +--[tap0]---+
|
|
| | | |
|
|
[lisp0] OVS1 [eth0]-----------------[eth0] OVS2 [lisp0]
|
|
| | | |
|
|
+----------+ +-----------+
|
|
|
|
On each hypervisor, interfaces tap0, eth0, and lisp0 are added to a single
|
|
bridge instance, and become numbered 1, 2, and 3 respectively:
|
|
|
|
ovs-vsctl add-br br0
|
|
ovs-vsctl add-port br0 tap0
|
|
ovs-vsctl add-port br0 eth0
|
|
ovs-vsctl add-port br0 lisp0 -- set Interface lisp0 type=lisp options:remote_ip=flow options:key=flow
|
|
|
|
Flows on br0 are configured as follows:
|
|
|
|
priority=3,dl_dst=02:00:00:00:00:00,action=mod_dl_dst:<VMx_MAC>,output:1
|
|
priority=2,in_port=1,dl_type=0x0806,action=NORMAL
|
|
priority=1,in_port=1,dl_type=0x0800,vlan_tci=0,nw_src=<EID_prefix>,action=set_field:<OVSx_IP>->tun_dst,output:3
|
|
priority=0,action=NORMAL
|
|
|
|
Optionally, if you want to use Instance ID in a flow, you can set it with
|
|
"action=set_tunnel:<IID>".
|