The blind replacement of strncpy() by ovs_strlcpy() is risky because
strncpy() never reads more bytes from its source string than necessary to
write its destination string, but ovs_strlcpy() and the OpenBSD function
that inspired it both read the entire source string. This avoids that
problem.
Given that change, we can use ovs_strlcpy() in a few more places, and
this commit does that too.
Coverity #10697,10696,10695,10694,10693,10692,10691,10690.
Without this commit, many of the unit tests for ofp-print.c fail with bus
errors on RISC architectures (tested on sparc) and presumably so would any
other code that uses these same struct members.
A few common IP protocol types were defined in "lib/packets.h". However,
we already assume the existence of <netinet/in.h> which contains a more
exhaustive list and should be available on POSIX systems.
We have a need to identify tunnels with keys longer than 32 bits. This
commit adds basic datapath and OpenFlow support for such keys. It doesn't
actually add any tunnel protocols that support 64-bit keys, so this is not
very useful yet.
The 'arg' member of struct odp_msg had to be expanded to 64-bits also,
because it sometimes contains a tunnel ID. This member also contains the
argument passed to ODPAT_CONTROLLER, so I expanded that action's argument
to 64 bits also so that it can use the full width of the expanded 'arg'.
Userspace doesn't take advantage of the new space though (it was only
using 16 bits anyhow).
This commit has been tested only to the extent that it doesn't disrupt
basic Open vSwitch operation. I have not tested it with tunnel traffic.
Signed-off-by: Ben Pfaff <blp@nicira.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Feature #3976.
Currently, Nicira error messages are non-overlapping with the OpenFlow
error definitions. This commit takes advantage of that by not taking
into account the vendor id. Printing error messages is likely to be
overhauled before long, and a more general approach can be taken then.
Before this commit, the first flow in "ovs-ofctl dump-flows" output was
printed on the same line as the OpenFlow message type name and the xid.
With this commit, that flow is put on a line of its own, like all of the
other flows in the output.
Requested-by: Paul Ingram <paul@nicira.com>
CC: Paul Ingram <paul@nicira.com>
Open vSwitch contains a few different chunks of code that need to decode
an OpenFlow message to determine its type and then validate that it is
long enough. Until now, the code for doing this has been more or less
scattered across the tree. Whenever a new piece of code needed to do this,
it generally needed to reimplement at least part of it.
This commit centralizes all of that work into a single function,
ofputil_decode_msg_type(), and helper functions, and converts all of the
code that was decoding messages by hand to use the new function.
Some code failed to convert tunnel IDs to host byte order for printing,
so this fixes that. Some code printed tunnel IDs with a 0x prefix and
other code didn't, so this code uses the '#' flag consistently (which
prints 0x for nonzero values and omits it for zero).
This commit also stops always printing all 8 digits. When tunnel IDs
are expanded to 64 bits, as they will be soon, printing 16 digits all the
time wastes too much space.
Acked-by: Jesse Gross <jesse@nicira.com>
The 'xid' in an ofp_header is not interpreted by the receiver but only by
the sender, so it need not be in any particular byte order. OVS used to
try to take advantage of this to avoid host/network byte order conversions
for this field. Older code in OVS, therefore, treats xid as being in host
byte order. However, as time went on, I forgot that I had introduced this
trick, and so newer code treats xid as being in network byte order.
This commit fixes up the situation by consistently treating xid as being
in network byte order. I think that this will be less surprising and
easier to remember in the future.
This doesn't fix any actual bugs except that some log messages would have
printed xids in the wrong byte order.
Our controller group at Nicira has requested a way to annotate flows with
extra information beyond the flow cookie. The new NXAST_NOTE action
provides such a way.
This new action is somewhat controversial. Some have suggested that it
should be added another way (either as part of the Nicira Extended Match
or as a new component of the flow_mod and related messages). Others think
that it has no place in the OpenFlow protocol at all and that an equivalent
should be implemented using the already available features of OVSDB. So
it is possible that this extension will be deleted and the feature will
be reimplemented some other way (or not at all).
CC: Teemu Koponen <koponen@nicira.com>
CC: Jeremy Stribling <strib@nicira.com>
When userspace and the kernel were using the same structure for flows,
flow_t was a useful way to indicate that a structure was really a userspace
flow instead of a kernel one, but now it's better to just write "struct
flow" for consistency, since OVS doesn't use typedefs for structs
elsewhere.
Acked-by: Jesse Gross <jesse@nicira.com>
The OpenFlow OFPAT_ENQUEUE action sets a queue id and outputs the packet
in one shot. There are times in which the queue should be set, but the
output port is not yet known. This commit adds the NXAST_SET_QUEUE and
NXAST_POP_QUEUE Nicira extension actions to modify the queue
configuration without requiring a port argument.
CC: Jeremy Stribling <strib@nicira.com>
CC: Keith Amidon <keith@nicira.com>
Add a tun_id field which contains the ID of the encapsulating tunnel
on which a packet was received (0 if not received on a tunnel). Also
add an action which allows the tunnel ID to be set for outgoing
packets. At this point there aren't any tunnel implementations so
these fields don't have any effect.
The matching is exposed to OpenFlow by overloading the high 32 bits
of the cookie as the tunnel ID. ovs-ofctl is capable of turning
on this special behavior using a new "tun-cookie" command but this
command is intentially undocumented to avoid it being used without
a full understanding of the consequences.
In a flow description, the VLAN VID was printed in hex, but an VLAN VID
modification would print the value in decimal. This commit consistently
prints the value in decimal.
CC: Paul Ingram <paul@nicira.com>
Clean-up a few items related to flow cookies:
- Allow setting the flow cookie as a hex or decimal string
- Consistently print the cookie in hex
- Document the ability to set the flow cookie in ovs-ofctl.
