2
0
mirror of https://github.com/openvswitch/ovs synced 2025-08-22 01:51:26 +00:00
ovs/NEWS

374 lines
16 KiB
Plaintext
Raw Normal View History

post-v1.7.0
------------------------
- New FAQ. Please send updates and additions!
- ovs-ofctl:
- "mod-port" command can now control all OpenFlow config flags.
- OpenFlow:
- Allow general bitwise masking for IPv4 and IPv6 addresses in
IPv4, IPv6, and ARP packets. (Previously, only CIDR masks
were allowed.)
- Allow support for arbitrary Ethernet masks. (Previously, only
the multicast bit in the destination address could be individually
masked.)
- Additional protocols are not mirrored and dropped when forward-bpdu is
false. For a full list, see the ovs-vswitchd.conf.db man page.
- Open vSwitch now sends RARP packets in situations where it previously
sent a custom protocol, making it consistent with behavior of QEMU and
VMware.
v1.7.0 - xx xxx xxxx
------------------------
- kernel modules are renamed. openvswitch_mod.ko is now
openvswitch.ko and brcompat_mod.ko is now brcompat.ko.
- Increased the number of NXM registers to 8.
- Added ability to configure dscp setting for manager and controller
connections. By default, these connections have a DSCP value of
Internetwork Control (0xc0).
- Added the granular link health statistics, 'cfm_health', to an
interface.
- OpenFlow:
- Added support to mask nd_target for ICMPv6 neighbor discovery flows.
- Added support for OpenFlow 1.3 port description (OFPMP_PORT_DESC)
multipart messages.
- ovs-ofctl:
- Added the "dump-ports-desc" command to retrieve port
information using the new port description multipart messages.
- ovs-test:
- Added support for spawning ovs-test server from the client.
- Now ovs-test is able to automatically create test bridges and ports.
- "ovs-dpctl dump-flows" now prints observed TCP flags in TCP flows.
- The "coverage/log" command previously available through ovs-appctl
has been replaced by "coverage/show". The new command replies with
coverage counter values, instead of logging them.
v1.6.1 - 25 Jun 2012
------------------------
- Allow OFPP_CONTROLLER as the in_port for packet-out messages.
v1.6.0 - 24 Feb 2012
------------------------
*** Internal only release ***
- bonding
- LACP bonds no longer fall back to balance-slb when negotiations fail.
Instead they drop traffic.
- The default bond_mode changed from SLB to active-backup, to protect
unsuspecting users from the significant risks of SLB bonds (which are
documented in vswitchd/INTERNALS).
- Load balancing can be disabled by setting the bond-rebalance-interval
to zero.
- OpenFlow:
- Added support for bitwise matching on TCP and UDP ports.
See ovs-ofctl(8) for more information.
- NXM flow dumps now include times elapsed toward idle and hard
timeouts.
- Added an OpenFlow extension NXT_SET_ASYNC_CONFIG that allows
controllers more precise control over which OpenFlow messages they
receive asynchronously.
- New "fin_timeout" action.
- Added "fin_timeout" support to "learn" action.
- New Nicira action NXAST_CONTROLLER that offers additional features
over output to OFPP_CONTROLLER.
- When QoS settings for an interface do not configure a default queue
(queue 0), Open vSwitch now uses a default configuration for that
queue, instead of dropping all packets as in previous versions.
- Logging:
- Logging to console and file will have UTC timestamp as a default for
all the daemons. An example of the default format is
2012-01-27T16:35:17Z. ovs-appctl can be used to change the default
format as before.
- The syntax of commands and options to set log levels was simplified,
to make it easier to remember.
- New support for limiting the number of flows in an OpenFlow flow
table, with configurable policy for evicting flows upon
overflow. See the Flow_Table table in ovs-vswitch.conf.db(5)
for more information.
- New "enable-async-messages" column in the Controller table. If set to
false, OpenFlow connections to the controller will initially have all
asynchronous messages disabled, overriding normal OpenFlow behavior.
- ofproto-provider interface:
- "struct rule" has a new member "used" that ofproto implementations
should maintain by updating with ofproto_rule_update_used().
- ovsdb-client:
- The new option --timestamp causes the "monitor" command to print
a timestamp with every update.
- CFM module CCM broadcasts can now be tagged with an 802.1p priority.
v1.5.0 - 01 Jun 2012
2011-11-30 23:41:19 -08:00
------------------------
- OpenFlow:
- Added support for querying, modifying, and deleting flows
based on flow cookie when using NXM.
- Added new NXM_PACKET_IN format.
- Added new NXAST_DEC_TTL action.
- ovs-ofctl:
- Added daemonization support to the monitor and snoop commands.
- ovs-vsctl:
- The "find" command supports new set relational operators
{=}, {!=}, {<}, {>}, {<=}, and {>=}.
- ovsdb-tool now uses the typical database and schema installation
directories as defaults.
- The default MAC learning timeout has been increased from 60 seconds
to 300 seconds. The MAC learning timeout is now configurable.
2011-11-30 23:41:19 -08:00
v1.4.0 - 30 Jan 2012
2011-10-25 12:37:26 -07:00
------------------------
- Compatible with Open vSwitch kernel module included in Linux 3.3.
- New "VLAN splinters" feature to work around buggy device drivers
in old Linux versions. (This feature is deprecated. When
broken device drivers are no longer in widespread use, we will
delete this feature.) See ovs-vswitchd.conf.db(5) for more
information.
- OpenFlow:
- Added ability to match on IPv6 flow label through NXM.
- Added ability to match on ECN bits in IPv4 and IPv6 through NXM.
- Added ability to match on TTL in IPv4 and IPv6 through NXM.
- Added ability to modify ECN bits in IPv4.
- Added ability to modify TTL in IPv4.
- ovs-vswitchd:
- Don't require the "normal" action to use mirrors. Traffic will
now be properly mirrored for any flows, regardless of their
actions.
- Track packet and byte statistics sent on mirrors.
- The sFlow implementation can now usually infer the correct agent
device instead of having to be told explicitly.
- ovs-appctl:
- New "fdb/flush" command to flush bridge's MAC learning table.
- ovs-test:
- A new distributed testing tool that allows one to diagnose performance
and connectivity issues. This tool currently is not included in RH or
Xen packages.
- RHEL packaging now supports integration with Red Hat network scripts.
- bonding:
- Post 1.4.*, OVS will be changing the default bond mode from balance-slb
to active-backup. SLB bonds carry significant risks with them
(documented vswitchd/INTERNALS) which we want to prevent unsuspecting
users from running into. Users are advised to update any scripts or
configuration which may be negatively impacted by explicitly setting
the bond mode which they want to use.
2011-10-25 12:37:26 -07:00
v1.3.0 - 09 Dec 2011
------------------------
- OpenFlow:
- Added an OpenFlow extension which allows the "output" action to accept
NXM fields.
- Added an OpenFlow extension for flexible learning.
- Bumped number of NXM registers from four to five.
- ovs-appctl:
- New "version" command to determine version of running daemon.
- If no argument is provided for "cfm/show", displays detailed
information about all interfaces with CFM enabled.
- If no argument is provided for "lacp/show", displays detailed
information about all ports with LACP enabled.
- ovs-dpctl:
- New "set-if" command to modify a datapath port's configuration.
- ovs-vswitchd:
- The software switch now supports 255 OpenFlow tables, instead
of just one. By default, only table 0 is consulted, but the
new NXAST_RESUBMIT_TABLE action can look up in additional
tables. Tables 128 and above are reserved for use by the
switch itself; please use only tables 0 through 127.
- Add support for 802.1D spanning tree (STP).
Implement new fragment handling policy. Until now, OVS has handled IP fragments more awkwardly than necessary. It has not been possible to match on L4 headers, even in fragments with offset 0 where they are actually present. This means that there was no way to implement ACLs that treat, say, different TCP ports differently, on fragmented traffic; instead, all decisions for fragment forwarding had to be made on the basis of L2 and L3 headers alone. This commit improves the situation significantly. It is still not possible to match on L4 headers in fragments with nonzero offset, because that information is simply not present in such fragments, but this commit adds the ability to match on L4 headers for fragments with zero offset. This means that it becomes possible to implement ACLs that drop such "first fragments" on the basis of L4 headers. In practice, that effectively blocks even fragmented traffic on an L4 basis, because the receiving IP stack cannot reassemble a full packet when the first fragment is missing. This commit works by adding a new "fragment type" to the kernel flow match and making it available through OpenFlow as a new NXM field named NXM_NX_IP_FRAG. Because OpenFlow 1.0 explicitly says that the L4 fields are always 0 for IP fragments, it adds a new OpenFlow fragment handling mode that fills in the L4 fields for "first fragments". It also enhances ovs-ofctl to allow users to configure this new fragment handling mode and to parse the new field. Signed-off-by: Ben Pfaff <blp@nicira.com> Bug #7557.
2011-10-19 21:33:44 -07:00
- Fragment handling extensions:
- New OFPC_FRAG_NX_MATCH fragment handling mode, in which L4
fields are made available for matching in fragments with
offset 0.
- New NXM_NX_IP_FRAG match field for matching IP fragments (usable
via "ip_frag" in ovs-ofctl).
- New ovs-ofctl "get-frags" and "set-frags" commands to get and set
fragment handling policy.
- CAPWAP tunneling now supports an extension to transport a 64-bit key.
By default it remains compatible with the old version and other
standards-based implementations.
- Flow setups are now processed in a round-robin manner across ports
to prevent any single client from monopolizing the CPU and conducting
a denial of service attack.
- Added support for native VLAN tagging. A new "vlan_mode"
parameter can be set for "port". Possible values: "access",
"trunk", "native-tagged" and "native-untagged".
- test-openflowd has been removed. Please use ovs-vswitchd instead.
2011-08-03 15:09:45 -07:00
v1.2.0 - 03 Aug 2011
------------------------
- New "ofproto" abstraction layer to ease porting to hardware
switching ASICs.
- Packaging for Red Hat Enterprise Linux 5.6 and 6.0.
- Datapath support for Linux kernels up to 3.0.
- OpenFlow:
- New "bundle" and "bundle_load" action extensions.
- Database:
- Implement table unique constraints.
- Support cooperative locking between callers.
- ovs-dpctl:
- New "-s" option for "show" command prints packet and byte
counters for each port.
- ovs-ofctl:
- New "--readd" option for "replace-flows".
- ovs-vsctl:
- New "show" command to print an overview of configuration.
- New "comment" command to add remark that explains intentions.
- ovs-brcompatd has been rewritten to fix long-standing bugs.
- ovs-openflowd has been renamed test-openflowd and moved into the
tests directory. Its presence confused too many users. Please
use ovs-vswitchd instead.
- New ovs-benchmark utility to test flow setup performance.
- A new log level "off" has been added. Configuring a log facility
"off" prevents any messages from being logged to it. Previously,
"emer" was effectively "off" because no messages were ever logged at
level "emer". Now, errors that cause a process to exit are logged
at "emer" level.
- "configure" option --with-l26 has been renamed --with-linux, and
--with-l26-source has been renamed --with-linux-source. The old
names will be removed after the next release, so please update
your scripts.
- The "-2.6" suffix has been dropped from the datapath/linux-2.6 and
datapath/linux-2.6/compat-2.6 directories.
- Feature removals:
- Dropped support for "tun_id_from_cookie" OpenFlow extension.
Please use the extensible match extensions instead.
- Removed the Maintenance_Point and Monitor tables in an effort
to simplify 802.1ag configuration.
- Performance and scalability improvements
- Bug fixes
2011-04-05 22:17:03 -07:00
v1.1.0 - 05 Apr 2011
------------------------
- Ability to define policies over IPv6
- LACP
- 802.1ag CCM
- Support for extensible match extensions to OpenFlow
- QoS:
- Support for HFSC qdisc.
- Queue used by in-band control can now be configured.
- Kernel:
- Kernel<->userspace interface has been reworked and should be
close to a stable ABI now.
- "Port group" concept has been dropped.
- GRE over IPSEC tunnels
- Bonding:
- New active backup bonding mode.
- New L4 hashing support when LACP is enabled.
- Source MAC hash now includes VLAN field also.
- miimon support.
- Greatly improved handling of large flow tables
- ovs-dpctl:
- "show" command now prints full vport configuration.
- "dump-groups" command removed since kernel support for
port groups was dropped.
- ovs-vsctl:
- New commands for working with the new Managers table.
- "list" command enhanced with new formatting options and --columns
option.
- "get" command now accepts new --id option.
- New "find" command.
- ovs-ofctl:
- New "queue-stats" command for printing queue stats.
- New commands "replace-flows" and "diff-flows".
- Commands to add and remove flows can now read from files.
- New --flow-format option to enable or disable NXM.
- New --more option to increase OpenFlow message verbosity.
- Removed "tun-cookie" command, which is no longer useful.
- ovs-controller enhancements for testing various features.
- New ovs-vlan-test command for testing for Linux kernel driver VLAN
bugs. New ovs-vlan-bug-workaround command for enabling and
disabling a workaround for these driver bugs.
- OpenFlow support:
- "Resubmit" actions now update flow statistics.
2011-04-05 22:17:03 -07:00
- New "register" extension for use in matching and actions, via NXM.
- New "multipath" experimental action extension.
- New support for matching multicast Ethernet frames, via NXM.
- New extension for OpenFlow vendor error codes.
- New extension to set the QoS output queue without actually
sending to an output port.
- Open vSwitch now reports a single flow table, instead of
separate hash and wildcard tables. This better models the
current implementation.
- New experimental "note" action.
- New "ofproto/trace" ovs-appctl command and associated utilities
to ease debugging complex flow tables.
- Database:
- Schema documentation now includes an entity-relationship diagram.
- The database is now garbage collected. In most tables,
unreferenced rows will be deleted automatically.
- Many tables now include statistics updated periodically by
ovs-vswitchd or ovsdb-server.
- Every table now has an "external-ids" column for use by OVS
integrators.
- There is no default controller anymore. Each bridge must have its
controller individually specified.
- The "fail-mode" is now a property of a Bridge instead of a Controller.
- New versioning and checksum features.
- New Managers table and manager_options column in Open_vSwitch table
for specifying managers. The old "managers" column in the
Open_vSwitch table has been removed.
- Many "name" columns are now immutable.
- Feature removals:
- Dropped support for XenServer pre-5.6.100.
- Dropped support for Linux pre-2.6.18.
- Dropped controller discovery support.
- Dropped "ovs-ofctl status" and the OpenFlow extension that it used.
Statistics reporting in the database is a rough equivalent.
- Dropped the "corekeeper" package (now separate, at
http://openvswitch.org/cgi-bin/gitweb.cgi?p=corekeeper).
- Performance and scalability improvements
- Bug fixes
2010-09-13 21:55:56 -07:00
v1.1.0pre2 - 13 Sep 2010
------------------------
- Bug fixes
v1.1.0pre1 - 31 Aug 2010
------------------------
2010-08-31 14:16:14 -07:00
- OpenFlow 1.0 slicing (QoS) functionality
- Python bindings for configuration database (no write support)
- Performance and scalability improvements
- Bug fixes
2010-05-31 22:31:07 -07:00
v1.0.1 - 31 May 2010
--------------------
- New "patch" interface type
- Bug fixes
2010-05-15 00:23:50 -07:00
v1.0.0 - 15 May 2010
--------------------
- Configuration database with remote management
- OpenFlow 1.0
- GRE tunneling
- Support for XenServer 5.5 and 5.6
- Performance and scalability improvements
- Bug fixes
v0.99.2 - 18 Feb 2010
---------------------
- Bug fixes
v0.99.1 - 25 Jan 2010
---------------------
- Add support for sFlow(R)
- Make headers compatible with C++
- Bug fixes
v0.99.0 - 14 Jan 2010
---------------------
- User-space forwarding engine
- Bug fixes
2009-11-29 11:23:32 -08:00
v0.90.7 - 29 Nov 2009
---------------------
- Add support for NetFlow active timeouts
- Bug fixes
2009-10-06 14:25:36 -07:00
v0.90.6 - 6 Oct 2009
--------------------
- Bug fixes
2009-09-21 13:08:12 -07:00
v0.90.5 - 21 Sep 2009
2009-09-07 20:44:25 -07:00
---------------------
- Generalize in-band control to more diverse network setups
- Bug fixes